Prepare vehicle Safety Warning Light installed before the start of the following tools : .. 1 flathead screwdriver, Phillips screwdriver, 2 , 3 insulating tape , 4 towels, 5 pliers.
1 marked the first shop beside the trunk of a car towel , with a flathead screwdriver pry logo, shop towel to prevent scratching the body 2 . Attention first double-sided adhesive peel the body , when the prying force is moderate, not too fierce , little by little , slowly pry down , cleaning the car standard and the car body sided adhesive 3 with a Phillips screwdriver to remove the interior rear bulkhead , note that some places have clips, be careful operating noise removed board can see various lines . 4 now come standard installation of car lights, car standard lamp power line through one of the car standard positioning holes , wear to tear inside the trunk of the car beacon -sided adhesive on the back , while the cable side of the car beacon light stick to the car body , the pressure tight. 5 car Safety Beacon Warning
Light installed, then the power now . Vehicle beacon light to pick license after power lights , so when you turn the car standard lamp night light will also open , to find the license plate lamp power connector 6 . Unplug the plug, a hole in the positive and negative of each strip , exposing the wire core , according to red to red , black to black -wired , do not forget to wrap with insulating tape and, finally, re- plug back ! Replace the tail cover insulation board !
图片
2014年4月8日星期二
2014年3月23日星期日
Stars Safety Warning Light Features and Benefits
A solar-powered, no cables, providing clean energy lighting anywhere.
(2) using lithium iron phosphate batteries, long-lasting, energy, environmental protection, the use of more than 5 years maintenance free.
3 super bright LED light, red, yellow, blue, green and white light sources to choose from, and supporting the five-color shade.
4 Stars Safety Warning Light integrated management design, available in 12 pre-programmed flashing mode, and flicker via infrared remote control mode switch; and ensure that in daylight and cloudy weather automatic rapid charging.
5 polycarbonate resin concave border shell, durable, waterproof, dustproof, 360-degree viewing range of up to 3 kilometers.
6 automatically shut down during the day, automatically turns on at night can also manually open and close.
7 Dimensions 130 * 130 * 135mm Weight 850g.
(2) using lithium iron phosphate batteries, long-lasting, energy, environmental protection, the use of more than 5 years maintenance free.
3 super bright LED light, red, yellow, blue, green and white light sources to choose from, and supporting the five-color shade.
4 Stars Safety Warning Light integrated management design, available in 12 pre-programmed flashing mode, and flicker via infrared remote control mode switch; and ensure that in daylight and cloudy weather automatic rapid charging.
5 polycarbonate resin concave border shell, durable, waterproof, dustproof, 360-degree viewing range of up to 3 kilometers.
6 automatically shut down during the day, automatically turns on at night can also manually open and close.
7 Dimensions 130 * 130 * 135mm Weight 850g.
2014年3月19日星期三
Stars Safety Warning Light Lightbar How to Install
Long row of warning lights installed in the vehicle without the punch, will not damage the body. Can be fixed with a retractor, retractors while the fixed side of the door edge fixed lamp body. Alarm transmission is usually mounted in front of the location in the ashtray, and the other in the seat around the transmission surface of the plastic plate.
Specific installation methods:
The first step: first Stars Safety Warning Lightinto the roof, the tripod screw hole locations can be aligned with the car door post,
Step two: After comparing retractors pitch, and then fixed hooks on the screws.
The third step: the retractor and distribution of screws, the long lights fixed tight. (Hand pushed a little bounce light can not stand)
Step Four: The long lamp power cord loose, according to the following figure laying.
Step Five: After the completion of the laying of the line, then the power of positive and negative.
Specific installation methods:
The first step: first Stars Safety Warning Lightinto the roof, the tripod screw hole locations can be aligned with the car door post,
Step two: After comparing retractors pitch, and then fixed hooks on the screws.
The third step: the retractor and distribution of screws, the long lights fixed tight. (Hand pushed a little bounce light can not stand)
Step Four: The long lamp power cord loose, according to the following figure laying.
Step Five: After the completion of the laying of the line, then the power of positive and negative.
订阅：
博文 (Atom)